MSDS - Nylon Brushes

Section 1 - Product Identification:
Manufacturer's Name: Anderson Products - One Weiler Drive - Cresco, PA 18326
Information and Emergency No.: (800) 755-6101
Date Prepared: January 9, 2012

Section 2 - Hazardous Ingredients:

Hazardous Component/
Common Name

CAS #
%
By Weight
OSHA
PEL
ACGIH
TLV
SARA
Title III
RQ
LBS

Nylon 612
Non-regulated stabilizer, lubricants and coolants

Material is not known to contain toxic chemicals under Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR part 372.

26098-55-5
-

>98
<2

*N/A
*N/A

*N/A
*N/A
*N/A
*N/A
*N/A
*N/A

Section 3 - Hazards Identification:

Emergency Overview: No adverse effects are expected from human exposure to polyhexamethylene adipamide, except for mechanical irritation of skin and eyes caused by particles. Significant skin permeation and systemic toxicity after contact appears unlikely.

Potential Health Effects from Inhalation, Skin, Eyes or Ingestion: *N/A

Carcinogenicity: NTP? No IARC Monographs? No OSHA Regulated? No

Section 4 - First Aid Measures:

Inhalation
No specific intervention is indicated as the compound is not likely to be hazardous by inhalation. If exposed to fumes from overheating or combustion, move to fresh air. Consult a physician if symptoms persist.
Ingestion
The compound is not likely to be hazardous by skin contact, but cleansing the skin after use is advisable. If molten polymer gets onto skin, cool rapidly with cold water. Do not attempt to peel polymer from skin. Obtain medical treatment for thermal burn.
Skin
In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Call a physician.
Eyes
No specific intervention is indicated as compound is not likely to be hazardous by ingestion. Consult a physician if necessary.

Section 5 - Fire Fighting Measures:
Flash Point (Method Used):
400° C (752° F) D1929
Flammable Limits:
LEL:
*N/A
UEL:
*N/A
Auto Ignition Temp:
752° F
NFPA Class: *N/A
General Hazards: Large molten masses may ignite spontaneously in air. Water quenching of such masses is good practice.
Extinguishing Media:
Water, foam, dry chemical, CO2
Fire Fighting Procedures:
Keep personnel removed and upwind of fire. Wear self-contained breathing apparatus.
Unusual Fire and Explosion Hazards:
Large molten masses may ignite spontaneously in air. Water quenching of such masses is good practice.
Hazardous Combustion Products: Ammonia, carbon monoxide, small amounts of hydrogen cyanide and aldehydes.

Section 6 - Accidental Release Measures:
Steps To Be Taken In Case Material Is Released Or Spilled:
Sweep up to prevent a slipping hazard.

Section 7 - Handling And Storage:
Precautions To Be Taken In Handling And Storage:
See first aid and protection information sections. Store in a cool, dry place. Keep containers tightly closed to prevent moisture absorption and contamination.

Section 8 - Exposure Controls/Personal Protection:
Engineering Controls: Use local ventilation to control fumes from hot processing.
Personal Protection:

Respiratory Protection (specify type)
NIOSH/MSHA approved air purifying respirator with an organic vapor cartridge and a dust/mist filter may be premissible under certain circumstances where airborne concentrations are expected to exceed exposure limits. Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any potential for an uncontrolled release, exposure levels are not known, or any other circumstance where air purifying respirators may not provide adequate protection.
Protective Gloves
*N/A
Eye/Face
Protection
Wear safety glasses. Wear coverall chemical splash goggles and face shield when possibility exists for eye and face contact due to splashing or spraying of molten material. A full face mask respirator provides protection from eye irritation.
Other Protective Clothing or Equipment
If there is a potential contact with hot/molten material, wear heat resistant clothing and footwear.
Work/Hygenic Practices
Avoid exposure to high concentrations of dust.

Section 9 - Physical And Chemical Properties:
Vapor Pressure (mm Hg.): *N/A
Vapor Density (AIR=1): *N/A
Specific Gravity (Water=1): 1.22 - 1.38
Evaporation Rate (Water=1): *N/A
Solubility in Water: Insoluble
Freezing Point: Solid at room temp
Ph:
*N/A
Appearance and Odor:
Odorless filaments
Boiling Point:
*N/A
Physical State: Solid
Viscosity: *N/A
Volatile Organic Compounds : ca 1% (water)

Section 10 - Stability And Reactivity:
Stability: Stable
Conditions to Avoid: Heating above 340° C
Incompatibility (Materials to Avoid):
Strong acids and oxidizing agents
Hazardous Decomposition or Byproducts: Cyclopentanone, carbon monoxide, aldehydes, ammonia
Hazardous Polymerization: Will not occur
Conditions to Avoid: *N/A


Section 11 - Toxicological Information:
No specific information available.

Section 12 - Ecological Information:
Toxicity is not known. Insoluble. Do not release to streams, ponds or lakes.

Section 13 - Disposal Considerations:
Waste Disposal Method: Preferred options for disposal are (1) recycling, (2) incineration with energy recovery, and (3) landfill. The high fuel value of this product makes option (2) very desirable for material that cannot be recycled. Treatment, storage, transportation and disposal must be in accordance with applicable federal, state/provincial and local regulations.

Section 14 - Transport Information:

Proper Shipping Name
*N/A - not DOT or TDG regulated
DOT Hazard Class/Pack Group
*N/A
Reference
*N/A
IATA Hazard Class/Pack Group
*N/A
IMDG Hazard Class
*N/A
UN/NA Identification Number
*N/A
RID/ADR Dangerous Goods Code
*N/A
Label
*N/A
UN TDG Class/Pack Group
*N/A
Hazard Symbols
*N/A

Note: Transportation information provided is for reference only. Client is urged to consult CFR 49 parts 100-177, IMDG, IATA, EC United Nations TDG, and WHMIS (Canada) TDG information manuals for detailed regulations and exceptions covering specific container sizes, packaging materials and methods of shipping.

Section 15 - Regulatory Information:
TSCA (Toxic Substance Control Act): In compliance with TSCA inventory requirements for commercial purposes.
SARA Title III (Superfund Amendments and Reauthorization Act): Material is not known to contain toxic chemicals under Section 313 of Title III of the Superfunds Amendments and Reauthorization Act of 1986 and 40 CFR part 372.
CERCLA (Comprehensive Response Compensation and Liability Act):
*N/A
CPR (Canadian Controlled Products Regulations): *N/A
IDL (Canadian Ingredient Disclosure List): *N/A
DSL/NDSL (Canadian Domestic Substances List/Non-Domestic Substances List): *N/A
EINECS (European Inventory of Existing Commercial Chemical Substances): *N/A
EC Risk Phrases: *N/A
EC Safety Phrases : See first aid and protection information sections.

Section 16 - Other Information:
Do not use the materials in the product to construct and object for permanent implantation in the human body. The use of the product in the manufacture of permanent implants is acceptable as long as any residue is removed from the implant surface.

HMIA Hazard Ratings:

Health
0
(0 = Insignificant, 3 = High)

Flammability

1

(1 = Slight, 4 = Extreme)
Reactivity
0
(2 = Moderate)
Personal Protective Equipment
A
Safety Glasses

Revision Summary: None
This MSDS has been revised in the following sections: None
MSDS Prepared By: Frank J. Hettes, Vice President - Innovation


*N/A = Not Applicable

The information contained herein is believed to be accurate but is not warranted to be so. Data and calculations are based on information furnished by the manufacturer of the product and manufacturers of the components of the product. Users are advised to confirm in advance of need that information is current, applicable and suited to the circumstances of use. Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety procedures are not adhered to as stipulated in the data sheet. Furthermore, vendor assumes no responsibility for injury caused by abnormal use of this material even if reasonable safety procedures are followed. Any questions regarding this product should be directed to the manufacturer of the product as described in Section 1.

Anderson Products Home
About Us | Products | Literature | MSDS Sheets | Copyright Info

E-mail: info@andersonproducts.com | Phone: 800-755-6101

All Rights Reserved, Copyright © Anderson Products 2001-2014